PA11 CF (Carbon fiber)

One of the strongest and most versatile materials available on the powder market dedicated to SLS printing technology.

Properties:

  • tensile and flexural strength
  • thermal resistance
  • impact resistance
  • good elongation at break
  • good chemical resistance
  • good surface quality
  • high stiffness

Applications:

  • Production maintenence: replacement parts, fixtures, jigs
  • Automotive: high-performance parts, metal replacement parts
  • Extreme applications: motorsports, lightweight structures, high temperature
  • Aerospace: lightweight structures, temperature
  • Research: mechanical parts, composite elements
  • Medicine: medical equipment, prosthetics

Watch webinar

Performance materials for special applications – learn more about PA12 Industrial, PA11 CF & Flexa Performance

Make the most of your material with simple, efficient powder recycling.

What is the refresh rate?

It is the ratio of a minimum amount of fresh powder needed in a mixture of material used in an SLS 3D printer. A lower refresh ratio means better cost-efficiency of the material.

How it works

The amount of needed fresh powder is automatically calculated by our software and shown on the printer screen after the print job is finished. Just add shown amount of material into the mixing cycle of used material and you can start your next job with refreshed material.

Sample print prices

Material
Printer
Material
Printer
Model
Full bed
Printing Costs

Order a sample model

printed with PA11 Carbon Fiber Powder

Specification

General information
Method
Material type
Nylon 11
Dedicated for
Lisa PRO, Lisa X
Software
Sinterit Studio Advanced
Material refreshing ratio¹
40 %
Nitrogen needed
Yes
Color
black
Mechanical properties
Tensile Strength (X direction)
65.93 MPa
PN-EN ISO 527-1:2012
Tensile Modulus (X direction)
4517 MPa
PN-EN ISO 527-1:2012
Flexural Strength (X direction)
87.35 MPa
PN-EN ISO 178:2019
Impact strength X (Charpy – unnotched)
64.53 kJ/m2
PN-EN ISO 179-1:2010
Thermal properties
Melting point
197 °C
PN-EN ISO 11357-3:2018
Heat deflection temperature A/B (X direction)
167 °C / 190 °C
PN-EN ISO 75-2:2013-06
1 Refresh ratio is the amount of refreshing powder that is required to be mixed after the printing with unsintered material.

Information provided within this document shows values for reference and comparison only. Parameters presented in this specification are subject to change without notice. Final part properties may vary based on a printed part design and orientation, material handling as well as printing environment (humidity and temperature). The manufacturer is responsible for validation whether the printout is accurate and fit for the intended purpose.


Compatible with
Daniel Aarts
Technical Director at Innoseal Europe

Sinterit’s Lisa X has allowed us to reduce lead-times and create better solutions — faster, helping us satisfy our customers. We have looked at other 3D printing methods, and other brands, but ultimately decided on SLS and chose Sinterit for their communication, and open material possibility. Something we couldn’t find in other suppliers of affordable entry level SLS printers.

Innoseal case study with Sinterit LISA X
Alberto Parolin
R&D Team Leader in BNP

Getting Lisa X solved a lot of our problems. It has a big enough printing area, so we almost always can print big components in one part. It wouldn’t be possible with competitive SLS 3D printing solutions.

LISA X in action case study BNP
Philippe Bendel
Additive Manufacturing Development Leader – Somfy

The main reason Somfy reached out for the SLS technology from Sinterit was productivity. Printing many pieces in one batch was a game-changer

Alec Bialek
Head of Jetson’s R&D

When we look at Lisa’s line of printers, or Sinterit at general compared to other companies, the two major things that we liked were the materials, that are open source, so we are not locked into one brand […]. We are able to look around the market and use a material that works best for the part.

Overcome Your Challenge with the Right 3D Printer

  • Costs of investment

  • Return of investment

  • After Sales Support

  • Printouts Quality

  • Available Materials

We are determined to help you!

Let experienced experts and engineers help you make the decision

































Discover Case Studies

See also powders:

PA12 Smooth
PA12 Onyx
PA11 ESD

FAQ

How should I store the printing powder?

How should I store the printing powder?
  • Store the powder at room conditions ( ~23°C and 50% humidity – the lower humidity the better)
  • Always store the material in a sealed dry box/container.
  • Do not leave the container open.
  • Clean the machine directly after printing and store the material immediately after removing the print cake.
  • Do not let the powder stay in the printer for more than a couple hours.
  • Put a few silicone absorbers in the container (but don’t add them to the printer)

Contact Sinterit support with your questions.

What is the difference between “Fresh” powder and “Starter powder”?

Starter powder is basically a print-ready powder.

In Sinterit we distinguish three powder conditions: print-readyused, and fresh.

Used is a type of powder that you get after the printing, present in overflow bin or remaining after printout cleaning.
Fresh is a type of powder that is being used for refreshing the powder. After mixing this powder with used powder you will receive print-ready.
Print-ready is a type of powder that you can simply pour into the printer and start printing.
Although printing using Fresh is possible it’s not economically optimal therefore Sinterit printers are optimized for using a refreshed (print-ready) powder.

Why do I need an ATEX vacuum cleaner to clean powder?

SLS polyamide powder used for 3D printing is considered particulate matter because of its size. Polyamide powder particles are generally 40 micrometers or smaller. If vacuumed in an ordinary vacuum cleaner, the powder could cause an explosion.

Such materials are subject to labor regulations on air quality and occupational safety. The procedures call for appropriate maintenance of powder at work. Only certified industrial vacuum cleaners should be used to clean such materials. More information about the ATEX Vacuum cleaner can be found here.

Contact Sinterit support with your questions.

What is PA11 Carbon Fiber and what makes it special?

PA11 Carbon Fiber is a bio-derived composite powder based on Polyamide 11 and enhanced with carbon fibers. It offers superior mechanical strength, thermal resistance, and stiffness, making it one of the strongest SLS powders available.

What applications is it best suited for?

This material is ideal for high-performance automotive parts, motorsport components, aerospace models, prosthetics, maintenance tools, and mechanical parts in extreme environments.

Which printers is this material compatible with?

It is compatible with the Sinterit Lisa X and Lisa Pro printers.

Does it require nitrogen during the printing process?

Yes, nitrogen is required to print with PA11 Carbon Fiber.

What is the refresh ratio of this powder?

The refresh ratio is 40%, meaning 40% of the powder in a new job must be fresh.

What are the standout mechanical properties?

PA11 Carbon Fiber offers a tensile strength of up to 65.9 MPa, flexural strength up to 87.3 MPa, and impact resistance up to 73.9 kJ/m² (Charpy unnotched).

How thermally resistant is it?

It features a melting point of 197 °C and a heat deflection temperature (HDT B) of up to 190 °C in the X direction—one of the highest in Sinterit’s powder range.

What is the surface finish like?

PA11 Carbon Fiber provides good surface quality along with high stiffness, dimensional stability, and chemical resistance.

What color are the printed parts?

The powder and printed parts are black, which gives a professional, high-performance appearance.

Is this material sustainable?

Yes, it is bio-based and derived from castor oil, making it an environmentally conscious choice for high-end engineering applications.

Resources

PA11 CF(Carbon FIber)
Check the specification
DOWNLOAD
PA11 CF(Carbon Fiber)
Extended specification
DOWNLOAD
PA11 CF(Carbon Fiber)
Safety data sheet EN
DOWNLOAD
PA11 CF(Carbon Fiber)
Safety data sheet DE
DOWNLOAD
PA11 CF(Carbon Fiber)
Safety data sheet FR
DOWNLOAD
PA11 CF(Carbon Fiber)
Safety data sheet PL
DOWNLOAD

Pricing

Below there are approximate costs for some example models.
Be aware that the quotation assumes that there is only one piece printed. In SLS technology, the cost per part will be much lower with a higher number of elements printed at once.
  • Flexible
  • Standard
Model
Dimensions
PA12
Smooth
PA11
Onyx
Flexa
Grey
Flexa
Soft
TPE
Below
Model volume:
Model volume:
Total print height:
6.82 cm
Dimensions:
65 x 65 x 63 mm
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Total print height:
6.82 cm
Dimensions:
65 x 65 x 63 mm
49,90 €
49,90 €
49,90 €
49,90 €
49,90 €
49,90 €
Derailleur
Model volume:
28.12 cm^3
Total print height:
6.82 cm
Dimensions:
65 x 65 x 63 mm
71,80 €
71,80 €
71,80 €
71,80 €
71,80 €
71,80 €
Driller housing
Model volume:
28.12 cm^3
Total print height:
6.82 cm
Dimensions:
65 x 65 x 63 mm
157 €
157 €
157 €
157 €
157 €
157 €
Model
Dimensions
PA12
Smooth
PA11
Onyx
Flexa
Grey
Flexa
Soft
TPE
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
Crank
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
Model volume:
28.12 cm^3
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €
51,30 €

Get a free sample box

Universal joint + turbine
The free samplebox contains two printouts made from PA12 Smooth. They are both movable designs, and each one is printed in one piece.

These are examples showing high precision and freedom of design ensured by SLS technology.
order free sample box
Mamy też advanced samples orci varius natoque penatibus et magnis dis parturient montes, nascetur
ridiculus mus. Aliquam id placerat nunc. Integer viverra, arcu vel feugiat viverra, dui purus sodales libero.
SEE ADVANCED samples
This product includes GeoLite2 data created by MaxMind, available from https://www.maxmind.com.